A timber frame building with black-stained timber and white-stained wattle and daub panels
Timber framed buildings and internal beams are often admired for their pristine beauty and perfection but it is easy to forget that they are vulnerable to decay and damage if not properly maintained and repaired. Sadly, poorly thought out alterations and the use of inappropriate materials have frequently wrought havoc with the timbers, not only causing damage aesthetically but structurally, with the result that they are no longer adequate to bear the loads placed upon them.
Potential timber frame problems
- Dampness that may be causing timbers to rot.
- Signs of fungal attack.
- Signs of beetle infestation such as powder or ‘frass’.
- Structural failure in lintels above doors and windows.
- Movement in timber frames and failing joints.
- Sagging beams that might be overloaded.
- Timbers that have been cut through during alterations.
Left-right: The town of Thaxted in Essex is renowned for its concentration of medieval timber framed houses; A timber frame undergoing major repairs; Carved details on a limewashed timber frame
Even where no timber is visible, it is worth remembering that it is likely to be present. As well as being used for complete frames, timber was employed for lintels above doors and windows, joists and other elements. In some cases, changes in fashion, or the need to make timber framed buildings more weatherproof, meant that they were rendered over externally or were clad in tile hanging, while some were ‘re-fronted’ in brick or stone.
Understanding the way timber has been used and its structural importance is vital when assessing its condition, carrying out repairs or making alterations. For these reasons it is advisable to employ a surveyor or structural engineer with experience of buildings of the same type and age when problems are suspected or major work is to be done.
Left-right: Original features such as these carpenters’ marks are easily lost through the use of over zealous or abrasive cleaning methods. For more advice on making sympathetic repairs and finding a conservation builder in your area, contact SPAB; A timber framed house in Sussex: the original wattle and daub panels have been replaced with flint and stone. The weight of such materials can distort a timber frame
Check for damage
Decay is the biggest enemy of timber and results from moisture, which leads to rot and beetle infestation. Always try to identify the source of dampness, such as blocked gutters or downpipes, inappropriate external cement renders or high ground levels and deal with these issues rather than just tackling the symptoms. Ensure the problem cannot occur again through repair and regular maintenance and monitor the affected areas after the issue appears to have been rectified.
Test suspect timber by prodding with a penknife: sound timber will resist penetration. Most old buildings have evidence of beetle attack but much of this is historic and unlikely to be of concern. Active beetle infestation is often revealed by fine dust or ‘frass’ where the insects have emerged through ‘exit’ holes. Where holes are present, look carefully to see if their walls are dark and dirty. If they are, the attack is likely to be historic rather than live. Clean, light coloured holes are probably more recent.
In the past, timber was often assessed and tidied up by ‘defrassing’ — slicing off the affected timber. This is a highly destructive process that radically alters its appearance and results in the loss of the original surface.
Left-right: A craftsman makes timber repairs; Repairs are made to the soleplate – the horizontal timber at the base of the wall frame; Traditional wattle and daub can be seen between the timbers
Where an assessment is required to ascertain the structural integrity of a beam, non-destructive techniques are now available. At its simplest, this involves drilling into the timber with a fine drill bit but specialist companies can undertake more accurate testing.
Bear in mind that timber treatment relying on the use of chemicals will only deal with the symptoms of the problem, not the cause. Chemical treatment is generally unnecessary if the source of the dampness has been removed and the timber has dried out because further decay will be limited if not halted completely.
Painted and treated beams
Many beams have been painted or have darkened with age but think hard before attempting to clean or strip them: in a few moments ‘cleaning’ can destroy the patina of age that has accumulated over hundreds of years. Dirt and dust can usually be removed with a soft brush or damp cloth. Avoid using linseed oil on beams as it stays sticky and attracts dirt. If a finish is desired, apply a thin coat of beeswax polish.
Removing paint from beams requires patience, time and effort. Never use shot blasting or other abrasive methods — the surface of the timber may be removed and worm eaten wood underneath revealed. In addition, the original shape and texture of the beam will be lost.
Liquid paint strippers, poultice systems or hot air guns may remove paint. Beware of the risk of fire and never use a blowtorch, protect surrounding areas and understand the dangers associated with removing lead paint. With any method, always test a small area first.
Left-right: Timber lintels are common in many buildings and are subject to rot; A scarf joint repair, where new wood has been introduced to shore up the existing timber.
Approach repairs with caution and consider the structural issues involved but never assume that timber needs replacing. Medieval beams were frequently much larger than were necessary so even where there is rot, the timber may still be capable of carrying the structural load.
Where damp problems exist, rafter feet and the ends of timbers built into brick or stonework often become saturated and rotten. Wherever possible avoid replacing timbers and instead make repairs so the least possible amount of original wood is lost.
One of the simplest, most honest and cost effective repair methods to rotten timbers is to use a metal strap. A strap can be made up by a local blacksmith and is simply bolted into place to hold decayed elements together. The strap method has the added benefit of being reversible and causing the least possible disturbance to the surrounding fabric of the building. Where it is necessary to cut out timber and make repairs, a good carpenter with an understanding of old buildings should be able to scarf in new sections using traditional jointing methods.
A major problem with timbers is that electricians and plumbers ‘notch’ into the top of joists in order to lay cables or pipes, dramatically weakening them. Where this has happened, joists can usually be strengthened with metal straps or by fitting additional joists alongside.
Hand-forged metal straps using a ‘D’ section bar are an honest, effective and reversible way of repairing a timber frame
Visit Roger Hunt’s website at huntwriter.com
|Buy Marianne Suhr and Roger Hunt’s “Old House Handbook”|